Rheem Performance XP75T06PV76U0 Instruction Manual

VACATIONWARNINGVERYHOTWARMA B CCOOLERHOTTERAP17509 (01/15)! FOR YOUR SAFETY!— Do not store or use gasoline or other flammable vapors or liquids or

10A new combination temperature and pressure relief valve, complying with the Standard for Relief Valves for Hot Water Supply Systems, ANSI Z21.22, is

11WARNING: DO NOT attempt to convert this water heater for use with a different type of gas other than the type shown on the rating plate. Such conver

12The water heater must be installed with the factory installed blower assembly in place.DANGER: Failure to install the blower assembly and properly v

13Maximum and Minimum Vent LengthsModelsAmbient Installation Temperatures and Vent System Material SpecicationsBelow 100°F 100°F to 125°F0 to 10 ft.E

14Vent Pipe ConnectionsTable 1From Sea level through 2000 ft. (609m) Above Sea levelModelVent System DiameterMin. Allowed Equivalent Vent Lengths (Ea

15 V Vent Terminal X Air Supply Inlet Area Where Terminal Is Not PermittedUS Installations1A - Clea

16NOTICE: All pipe, fittings, solvent cement, primers and procedures must conform to American National Standards Institute and American Society for Te

17-B-d.008d.0102' x 2' Sheet Metal Shield on Brick or Masonry WallsOutside ofBuildingTerminals with 1/2" Mesh Protective Screens Inside

18-B-d.008d.010 # Min. 12 in. (30.5 cm) Above Roof or Anticipated Snow Level; which ever is highest and Max. 24 in. (61 cm) Above Roof (Wi

19Condensate Management and Vent RisersThere is no condensate collection and disposal required for Rheem water heaters under most conditions. Installa

2Care and CleaningDraining ... 30Maintenance ... 30Vent System Inspection ... 31Burner Inspection ... 31Extended Shut-Do

20All joints in the vent piping must be properly sealed and the following materials are recommended:PVC materials should use ASTM D2564 grade cement.C

21WiringIf local codes permit, the water heater may be connected to electric service with the power cord provided (DO NOT use an extension cord). A gr

22Insulation BlanketsInsulation blankets, available to the general public, for external use on gas water heaters are not necessary. The purpose of an

23DO ❑ DO check inlet gas pressure to ensure that it is within the range specified on the rating plate. ❑ DO provide adequate air for combustion a

24Installation ChecklistA. Water Heater LocationB. Water SupplyC. Gas SupplyD. Relief ValveE. Venting ❑ Close to area of vent. ❑ Drain pan inst

25Tee fitting for vertical hot water supply lines.Hot water supply to houseFrom HOT outlet on water heaterHot water supply to heating unitSupplem

26Lighting the water heater Before operating this water heater, be sure to read and follow the instructions on the label pictured below and all other

27Safety Precautions DO turn off manual gas shut-off valve if water heater has been subjected to over heating, fire, flood, physical damage or if th

28Water Temperature SettingMaximum water temperatures occur just after the burner has shut off. To determine the water temperature, turn on a hot wate

29Sequence of OperationDuring initial start-up or a call for heat, the control will verify the vacuum switch is open.Once the control verifies the blo

3Be sure to read and understand the entire Use and Care Manual before attempting to install or operate this water heater. It may save you time and mon

30DANGER: Failure to perform the recommended Routine Preventative Maintenance can harm the proper operation of this water heater, which can cause carb

31HousekeepingVisually inspect the hot surface ignitor.To ensure sufficient ventilation and combustion air supply, proper clearances must be maintaine

32Vacation and Extended Shut-DownIf the water heater is to remain idle for an extended period of time, the power and water to the appliance should be

33Before You Call For ServiceTroubleshooting TipsSave time and money! Review the charts on the following pages first and you may not need to call for

34Before You Call For ServiceTroubleshooting TipsSave time and money! Review the charts on the following pages first and you may not need to call for

35Gas Control (Thermostat) Status CodesCAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and d

36Replacement PartsFor 75 gallon models using Natural or LP gas.Instructions For Placing a Parts OrderAll parts orders should include: The model and

37Notes:

38Notes:

39Notes:

4Time/Temperature Relationship in Scalds Water Temperature Time To Produce a Serious Burn 120°F More than 5 minutes 125°F 11/2 to 2 minutes 130

40IF YOU NEED SERVICE1. Should you have any questions about your new water heater, or if it requires adjustment, repair, or routine maintenance, it

5LP and Natural gas have an odorant added to aid in detecting a gas leak. Some people may not physically be able to smell or recognize this odorant. I

6IMPORTANT SAFETY INFORMATIONREAD ALL INSTRUCTIONS BEFORE USING!WARNING!For your safety, the information in this manual must be followed to minimize t

7Combustion Air Inlet OpeningsInstalling the water heaterThis water heater must be installed in accordance with these instructions, local codes, utili

8Combustion and Ventilation AirVentilation (ambient) air temperature must be 100°F or less. Proper operation of the water heater requires air for comb

9Thermal ExpansionDetermine if a check valve exists in the inlet water line. Check with your local water utility company. It may have been installed i